Wacker plates

[Giles]

Need one of these!! lol the price of that what a joke

 

[V8Druid]

Need one of these!! lol the price of that what a joke

interesting concept though, but would need a wider track for any proper weight

 

[Giles]

interesting concept though, but would need a wider track for any proper weight

140kg rating

 

[V8Druid]

140kg rating

yeh see that, but made out of ali and too narrow to put anything serious on the hook

interesting concept though, but would need a wider track for any proper weight

 

[Stroppymonkey]

That's only good at the end of the day not the beginning lol

140kg!? You'd want some very clean concrete for those little wheels

 

[Brendan]

Need one of these!! lol the price of that what a joke

Our local Travis have them for loading hire stuff, no idea they were that expensive to buy

 

[Russell]

Load Lift 300KG Penny Hydraulics FULL WORKING ORDER | eBay

Find many great new & used options and get the best deals for Load Lift 300KG Penny Hydraulics FULL WORKING ORDER at the best online prices at eBay! Free delivery for many products.

www.ebay.co.uk

 

[V8Druid]

Load Lift 300KG Penny Hydraulics FULL WORKING ORDER | eBay

Find many great new & used options and get the best deals for Load Lift 300KG Penny Hydraulics FULL WORKING ORDER at the best online prices at eBay! Free delivery for many products.

www.ebay.co.uk

I've put a few of them up over the last year ... always a couple on FB MP ... for a lot less .... seem a pretty decent sort of thing

 

[Stroppymonkey]

I've put a few of them up over the last year ... always a couple on FB MP ... for a lot less .... seem a pretty decent sort of thing

Handy for stoves and boilers, often been tempted. As you say cheap used ones pop up .

 

[6feetdown]

I've put a few of them up over the last year ... always a couple on FB MP ... for a lot less .... seem a pretty decent sort of thing

Handy for the dp2540

 

[Stroppymonkey]

Handy for the dp2540

No good for the DPU 100-70!

 

[6feetdown]

No good for the DPU 100-70!

Would get messy

 

[V8Druid]

Would get messy

if the hydraulics didn't let go ------ the back of the van might

 

[Rob65]

Would an engine crane not be a quick and cheep solution to loading an Whacker into van ?

I appreciate it would not move on anything other than good hard surfaces but would it be ok to lift Wacker and then revers van under it?

Not sure how heavy an engine crane is but I would have thought once flat packed it could comfortably be handled by two men.

 

[Stroppymonkey]

This has landed in the yard. Wanted to get it straight to play, but a flat battery stopped that till I gave it a charge. Quick look in the derv tank and the inline filter shows the usual crap and water so a full service in order before it goes out. Will hopefully take those bars off as well as they stick out. It’s a BIG lump - fingers crossed it will do what I need now and again for next year on the new shed project, then it’ll get sold on.
One big fly in the ointment is that the handle height adjuster is absent so the handle sits at knee height. Hopefully the seller will sort out - they’ve been very communicative so far, so fingers crossed. A wedge of plywood and a cable tie will get over the issue temporarily. Otherwise I’ll be moaning like Frick and on the phone to WN dealer next week.
The machine was allegedly fully checked over by the mechanic before it was sent out?

Thanks to @Storrsy for the link.

 

[Giles]

This has landed in the yard. Wanted to get it straight to play, but a flat battery stopped that till I gave it a charge. Quick look in the derv tank and the inline filter shows the usual crap and water so a full service in order before it goes out. Will hopefully take those bars off as well as they stick out. It’s a BIG lump - fingers crossed it will do what I need now and again for next year on the new shed project, then it’ll get sold on.
One big fly in the ointment is that the handle height adjuster is absent so the handle sits at knee height. Hopefully the seller will sort out - they’ve been very communicative so far, so fingers crossed. A wedge of plywood and a cable tie will get over the issue temporarily. Otherwise I’ll be moaning like Frick and on the phone to WN dealer next week.
The machine was allegedly fully checked over by the mechanic before it was sent out?

Thanks to @Storrsy for the link.

It just a bolt isn’t it with a rubber bush on the end?

Re the connecting arms You’ll need to swap the bolts for shorter ones that’s what I had to do when I took mine off

Don’t be tempted to test it on any concrete or tarmac etc get it on loose stuff before you try it

Mines a slow starter even with fresh battery don’t think they have a glow plug

 

[JD450A]

This has landed in the yard. Wanted to get it straight to play, but a flat battery stopped that till I gave it a charge. Quick look in the derv tank and the inline filter shows the usual crap and water so a full service in order before it goes out. Will hopefully take those bars off as well as they stick out. It’s a BIG lump - fingers crossed it will do what I need now and again for next year on the new shed project, then it’ll get sold on.
One big fly in the ointment is that the handle height adjuster is absent so the handle sits at knee height. Hopefully the seller will sort out - they’ve been very communicative so far, so fingers crossed. A wedge of plywood and a cable tie will get over the issue temporarily. Otherwise I’ll be moaning like Frick and on the phone to WN dealer next week.
The machine was allegedly fully checked over by the mechanic before it was sent out?

Thanks to @Storrsy for the link.

Let me know when you sell it

 

[Storrsy]

Let me know when you sell it

FFS stop being such a tart and just buy my old pedestrian roller of me

 

[JD450A]

FFS stop being such a tart and just buy my old pedestrian roller of me

Wasps Shove Arse Up
Re arrange the words

 

[Storrsy]

Wasps Shove Arse Up
Re arrange the words

One will cause you pleasure and the other will cause you pain. Il let you decide which is which .