Twin Drum Rollers

Davyk

Davyk

New member
I’m in the middle of building a new house and fortunately/unfortunately it involved constructing an 600m roadway which is now to be sheeted in 804 or similar following the majority of the construction traffic. The base layer is 3 inch down.

Going forward for maintenance I’m looking at getting a roller as hiring one works out at over €400 a time. I’ll give it run with the land leveller/box grader on a tractor followed by the roller. Topping up with stone as required.

I’ve settled on the idea of a 800mm roller as it takes up a lot less space than a 1.2m in the workshop when not in use.

Probably looking to buy in Euroauctions the likes of a JCB VMT160-80.
Any opinions on these they seem less complex than the newer Bomag/Hamm models.
 
Davyk

Davyk

New member
In looking o spend a little as possible. Something like this, seems to be the bottom of the market from
I’m in Ireland so euroaictions in Leeds is a good destination for plenty of trucks coming across the water
 
Last edited:
doobin

doobin

Well-known member
I’ve settled on the idea of a 800mm roller as it takes up a lot less space than a 1.2m in the workshop when not in use.
Scratch that idea immediately. Store it outside or build a new shed. But don’t buy an 800.

The compaction difference between an 800 and a 1200 is massive. 800 is a waste of time for something your scale.

If it’s staying on site then you might get a better deal buying something like a 130 even - something not towable.
 
S

Smiffy

Well-known member
I’m in the middle of building a new house and fortunately/unfortunately it involved constructing an 600m roadway which is now to be sheeted in 804 or similar following the majority of the construction traffic. The base layer is 3 inch down.

Going forward for maintenance I’m looking at getting a roller as hiring one works out at over €400 a time. I’ll give it run with the land leveller/box grader on a tractor followed by the roller. Topping up with stone as required.

I’ve settled on the idea of a 800mm roller as it takes up a lot less space than a 1.2m in the workshop when not in use.

Probably looking to buy in Euroauctions the likes of a JCB VMT160-80.
Any opinions on these they seem less complex than the newer Bomag/Hamm models.

Honestly for once a year you will use it I would just hire. Rollers only usually go to auction when they are knackered, in fact they only seem to get sold in general if they are knackered. They are the least looked after thing on site driven by people who don't care.
Also an 80 roller really needs about 8 passes to work properly. At I'm guessing around 3-4 meters wide and allowing for an overlap that is in the region of 64 times up and down the drive.
I would hire a big roller once a year that turns up and works and put the money towards something more versatile.
 
Regy53

Regy53

I like cake
Regy53

Regy53

I like cake
Mick-the-fitter

Mick-the-fitter

It’s what I do!
I’m in the middle of building a new house and fortunately/unfortunately it involved constructing an 600m roadway which is now to be sheeted in 804 or similar following the majority of the construction traffic. The base layer is 3 inch down.

Going forward for maintenance I’m looking at getting a roller as hiring one works out at over €400 a time. I’ll give it run with the land leveller/box grader on a tractor followed by the roller. Topping up with stone as required.

I’ve settled on the idea of a 800mm roller as it takes up a lot less space than a 1.2m in the workshop when not in use.

Probably looking to buy in Euroauctions the likes of a JCB VMT160-80.
Any opinions on these they seem less complex than the newer Bomag/Hamm models.
Agreed they are more similar to the old Terex rollers, by that I mean basic, not a lot of electronics.
 
hiluxman

hiluxman

Well-known member
£6k.... + VAT no buyers fee, will work on arrival as it should

run it two years il give you a guarantee buy back as long as its not smashed to buggery (bonnet etc) of 4k.



Can't knock that sort of deal.
 
Furniss

Furniss

Well-known member
£6k.... + VAT no buyers fee, will work on arrival as it should

run it two years il give you a guarantee buy back as long as its not smashed to buggery (bonnet etc) of 4k.



Will 3k buy it 🤔 seen as im still waiting for that dumper you promised ?
 
D

DaveDCB

Well-known member
I have roller dilemma all the time.. hire a roller 3 times a year and it equals the same as the depreciation on a new one! (With some funky man maths involved) they hold money so well if you use one occasionally it’s a no brainer, especially if it’s the end of year and abit of tax to burn!
 
V8Druid

V8Druid

do it as well as you can,but learn to do it better
In looking o spend a little as possible. Something like this, seems to be the bottom of the market from a dealer.
link deleted
I’m in Ireland so euroaictions in Leeds is a good destination for plenty of trucks coming across the water
do you realise your postcode is on that ebay link ??
 
Last edited:
Top