TiltyShaun
Well-known member
Fix it uk and keep it!!
Thomas7740
Well-known member
3 footer back, should be a good job
Thomas7740
Well-known member
Breaker fits 
Fuelled, greased, cleaned and loaded go ready to go back to factory job tomorrow
Fuelled, greased, cleaned and loaded go ready to go back to factory job tomorrow
V8Druid
do it as well as you can,but learn to do it better
grand weather there today too thenBreaker fits
View attachment 31993
Fuelled, greased, cleaned and loaded go ready to go back to factory job tomorrow
View attachment 31992
Thomas7740
Well-known member
Thomas7740
Well-known member
Two pits to dig out for filters and ventilation for spray booth. 9 inches concrete and 2 layers mesh to get through, then down a metre for concrete and L bars for shuttering the sides.
Handy day for the 60.
Handy day for the 60.
diggerjones
Well-known member
What about a bucket with teeth! 
GazCro
Well-known member
Handy day for a bigger hammer on a bigger machine
Thomas7740
Well-known member
Na, teeth get caught in the mesh and make life difficult, only scraping away and loading wee bits of concrete, no need for teethWhat about a bucket with teeth!
It’s not hard on either digger the way it’s being done so what’s your point? Paid per day so if it takes longer so be it
Be different if it was priced but it isn’t
GazCro
Well-known member
Those small silenced breakers are frustrating among mesh/rebar as the chisel isn't very long. I get ur paid per day but it's a boring day sitting pecking so I'd personally rather be getting on quicker.Na, teeth get caught in the mesh and make life difficult, only scraping away and loading wee bits of concrete, no need for teeth
It’s not hard on either digger the way it’s being done so what’s your point? Paid per day so if it takes longer so be it
doobin
Well-known member
Looks a neat and precise job.
Thomas7740
Well-known member
We didn’t do the cutting so don’t blame us for that
doobin
Well-known member
Looks fine apart from a wobble where it doesn't matter anyhow.We didn’t do the cutting so don’t blame us for that
V8Druid
do it as well as you can,but learn to do it better
I'll settle for it to just stop rainingBeen a rough few dayscan’t wait for summer
Thomas7740
Well-known member
Forgot the 60 was reaching her milestone, just an hour and a half late getting a photo
Big difference using the EZ26 on the breaker, no oil leaks and not needing the bonnet open to stay cool (even with new engine and bigger cored radiator the ex30 ran warm)
Big difference using the EZ26 on the breaker, no oil leaks and not needing the bonnet open to stay cool (even with new engine and bigger cored radiator the ex30 ran warm)
Thomas7740
Well-known member
Digging out nicely 
V8Druid
do it as well as you can,but learn to do it better
lovely digging ground
..... is that a block of concrete in the corner ?????
GazCro
Well-known member
Looks like it's sh*t ground if you wanted to build on it but that's often the best ground for digging nice.
Thomas7740
Well-known member
Have this on hire to dig footings, only got 830mm access 
Cracking wee digger, smoothest micro I’ve ever drove, with the smoothness, reach and load over height, it puts the E10 to shame. Not as powerful as an WN803 though. Only thing so far that lets it down imo is the boom doesn’t have enough offset to the left, no complaints elsewhere. Granted it’s about 50-60mm wider than an E10 but generally not an issue from my experience, although I understand everyone works in different areas etc
Only had it 3 days so opinion
could change by end of the week
Cracking wee digger, smoothest micro I’ve ever drove, with the smoothness, reach and load over height, it puts the E10 to shame. Not as powerful as an WN803 though. Only thing so far that lets it down imo is the boom doesn’t have enough offset to the left, no complaints elsewhere. Granted it’s about 50-60mm wider than an E10 but generally not an issue from my experience, although I understand everyone works in different areas etcOnly had it 3 days so opinion
Footer block 1