Furniss
Well-known member
That's exactly what I'm hoping for ...although in reality giving some reach up over the 8t.
6
6feetdown
Well-known member
Sods lawGot similar 3.7% on a new Timberwolf chipper through my usual finance guy at claas last month, Timberwolf’s subsidised offer through Arb lease was 1.5% more despite telling me I’d not get cheaper elsewhere!
Finally but the bullet on one after getting asked all the time if we had one, not been asked since
6
6feetdown
Well-known member
The avant with the forks has done so much I can't believe how much we use them.
Game changer
V8Druid
do it as well as you can,but learn to do it better
that'll not be far off with a swivelly hinge attached
Furniss
Well-known member
Build height direct mount shouldn't be too far off the s lock that's on the 6t in that photo and and tbf we should compare a tilty on both 8t and 6t so all things being equal photo is a fair comparison.
V8Druid
do it as well as you can,but learn to do it better
ah -- now you're sneaking in direct mount .. big difference then ... direct it'll still be a lot taller than with just the hitch as is .. would guess at 2-2.5X ... thought you were just hoping for as much reach as your exiting 8t on the new 6t
S
Smiffy
Well-known member
that'll not be far off with a swivelly hinge attached
Only for reaching out to grade though. If trying to reach to tip it won't be the same. I suppose you can do some twiddling and turn the bucket around as you reach. But it depends what you want it for.
I think it's easier just to accept certain things. You will never have enough reach and never have enough lift capacity.
Furniss
Well-known member
Looks like 10cm in it
S lock says 28cm
39cm I think on R2 rototilt - 38cm on engcon ec206.
V8Druid
do it as well as you can,but learn to do it better
looks about right
an additional 11cms for the hinge sounds optimistic
.. but 'spose they've measured itnote the extra 5 Deg.s between pins which all tilty manufacturers seem to factor in between upper and lower pins .... can't recall why ATM, but there is a reason and read it once .. Aiden might recall why?
top hitch'd double that up and end up with a stack at 67cms, mean
diggerjones
Well-known member
I remembered I'd got this video. First bucket full was very little in bucket 2nd bucket full i used the 4 in 1. But still i could of done better. The tauk coverter was knackered when this was filmed.
D
DaveDCB
Well-known member
Who shot the cameraman at the end?
diggerjones
Well-known member
I'm amazed you watched it till the end. I'm not in 
D
DaveDCB
Well-known member
I watched the whole 4 minutes in 10 seconds on super scroll speed.. it’s the best way to watch gunners videos as well, just skip to the end
diggerjones
Well-known member
Where's druid with the wanker emoji 
Gunners
Well-known member
I still get the money for this technique so please feel free to continueI watched the whole 4 minutes in 10 seconds on super scroll speed.. it’s the best way to watch gunners videos as well, just skip to the end
It pays for the pub
V8Druid
do it as well as you can,but learn to do it better
anyone else looking for a WN??
would the plate really be stuck on ???
in the 8t and below pages
forgot to post this last night
would the plate really be stuck on ???
in the 8t and below pages
forgot to post this last night
Furniss
Well-known member
I went to jersey to look at that.anyone else looking for a WN??
View attachment 45562
would the plate really be stuck on ???
View attachment 45561
in the 8t and below pages
forgot to post this last night
Vinpetrol
Well-known member
He does rabbit on a bitI watched the whole 4 minutes in 10 seconds on super scroll speed.. it’s the best way to watch gunners videos as well, just skip to the end
Vinpetrol
Well-known member
in my pursuit of a 2.5 - 3 tonne I've watched the Volvo v jcb enough times to get you well oiled !I still get the money for this technique so please feel free to continue
Footer block 1