The 'Today's Job' thread

[6feetdown]

Not done this for a while

 

[bobthebuilder]

Pushing on for kitchen install on the 4th of may

Drawing said 75mm but needed more to make all thresholds and levels work so got some 25mm as well

More insulation the better
I do try to stick layers together with the foam gun and do the joints and edges

 

[Lancs Lad]

Not done this for a while
View attachment 81038

Damn that's when I miss my dad old school chippy. Could hang a door in his sleep. Chisel...none of this routing out hinges.

 

[6feetdown]

Damn that's when I miss my dad old school chippy. Could hang a door in his sleep. Chisel...none of this routing out hinges.

I used both tbf, if you can make life easier do it.
Plus didn't have the guide bush for the hinge jig
It was actually nice to do a bit of finish work for a change, pre finished doors are great but also a pain.
At least my chisels are sharp again

 

[Lancs Lad]

I used both tbf, if you can make life easier do it.
Plus didn't have the guide bush for the hinge jig
It was actually nice to do a bit of finish work for a change, pre finished doors are great but also a pain.
At least my chisels are sharp again

Got a trend corner chisel?...remember showing dad one for the first time online. He ordered it there and then !

 

[6feetdown]

Got a trend corner chisel?...remember showing dad one for the first time online. He ordered it there and then !

Yes but still prefer a chisel if not using the jig.
Funny my chisel hand was cramping a few times whilst using it, not sure to a lack of liquid or getting older

 

[doobin]

Nice day for it.

 

[Bri963]

Does the seat spin, Doob?

 

[William127]

Neighbour started the bbq about 12.30, smelt bloody lovely
Going to be a lot of muck shifted out of here this week- already adding the micro digger to the hire from tomorrow to keep the pile tidy

 

[doobin]

Does the seat spin, Doob?

Yes, can lock it ‘side saddle’ too which is handy sometimes.

 

[6feetdown]

Getting there

 

[V8Druid]

Getting there
View attachment 81063

just adjusted the pic for you Andy .... what soil pipe ?????? -- this is a 'garden room', is it not?

 

[6feetdown]

just adjusted the pic for you Andy .... what soil pipe ?????? -- this is a 'garden room', is it not?
View attachment 81066

It's a customer not mine feel free to delete

 

[JD450A]

Digging holes for what will hopefully be my house soakaway..... Niggles me somewhat paying for a drainage design..... but will be cheap if it accelerates and reduces aggro with planning.
Pits ranged between 20min and 71 minutes..... At 1.5m the engineer specified..... Then I got pissed off and cracked out the BHL, 2.3M deep.... water goes in under 5 minutes.

 

[William127]

Good day today, despite an unexpected detour!
Second hand loncin on the dumper wet itself again, badly, wouldn't idle, sounded like a hit and miss and stank of fuel. Bit the bullet, 100 mile round trip and a brand new GX was in position
Lots of dirt to shift here, glad it's not my job! I'd have been doing it in a very different order but we're getting stuck in

 

[JD450A]

To the floor for the draw.

 

[doobin]

To the floor for the draw.

Looks very similar to mine.

Bet you paid less though

 

[JD450A]

Looks very similar to mine.

Bet you paid less though

25

Pleased with it now it's been lobotomized..... Ability to run it off 240V is ace too

 

[Lancs Lad]

25

Pleased with it now it's been lobotomized..... Ability to run it off 240V is ace too

You should wear a mask

 

[6feetdown]