CPS
Well-known member
Welding up a nice new bucket
V8Druid
do it as well as you can,but learn to do it better
going for it there Aiden ... new shroud, I'll wager a new tip and a weld to be justifiably proud of
MB36 torch, looking at the size of the shroud ????
CPS
Well-known member
Haha yea could have worn that hat with pride yesterdaygoing for it there Aiden ... new shroud, I'll wager a new tip and a weld to be justifiably proud of
View attachment 36139
MB36 torch, looking at the size of the shroud ????
500amp binze torch with new shroud and tip, run out of wire yesterday so sent the lad for refreshments
Wire has gone up well also
V8Druid
do it as well as you can,but learn to do it better
I bet it has .. has it trebled like the raw materials it's made from?? .... long time since I bought a roll of 1mm .... was about 18 quid for a 15 kilo roll ... shudder to think what it is nowHaha yea could have worn that hat with pride yesterday
500amp binze torch with new shroud and tip, run out of wire yesterday so sent the lad for refreshments
Wire has gone up well also
... still got a couple of rolls sat, so not gonna be finding out anytime soon 
Thomas7740
Well-known member
Feeling ambitious 
L
Lynchy
Well-known member
Lol quite a contrast,in my defence,I've done my time concreting,digging ballast,fixing crushers n heavy plant,seen most of the old guys retire knackered,decided not for me
CPS
Well-known member
£27.50 Yesterday.... nit as bad as I was expecting... I was hold £44 two weeks agoI bet it has .. has it trebled like the raw materials it's made from?? .... long time since I bought a roll of 1mm .... was about 18 quid for a 15 kilo roll ... shudder to think what it is now
CPS
Well-known member
20mm plate over 2k per tonpretty good considering the way steel has rocketed
V8Druid
do it as well as you can,but learn to do it better
it's all circa £2150/t average, ATM ... 's worse than "horrendous" ... never, ever, known it this high ... £1850 average was the previous worst, with some odd sections over £3k/t
doobin
Well-known member
Every time I need to order I have a five minute internal monologue with myself where I try to resist just cutting a section of of one of my workbenches...
"Go on, you could use a rounded edge next to the log burner anyway!
"
V8Druid
do it as well as you can,but learn to do it better
ROTFLMAOEvery time I need to order I have a five minute internal monologue with myself where I try to resist just cutting a section of of one of my workbenches...
"Go on, you could use a rounded edge next to the log burner anyway!
..... know the feeling ... "do you really need .???? ..."
CPS
Well-known member
Put it this way, Alot more time is spent now nesting parts into a sheet on the plasma
V8Druid
do it as well as you can,but learn to do it better
could do with a little time spent clearing the dross off the support bars too boyoView attachment 36157
Put it this way, Alot more time is spent now nesting parts into a sheet on the plasma
Quattromike
Well member-known
Was poking up some trusses today, caught a bit of sun
right good view point of benrinnes they have.
V8Druid
do it as well as you can,but learn to do it better
how do you insure yourself for jobs like that Mike? ... my cover for the cranes used to be horrendousView attachment 36170
Was poking up some trusses today, caught a bit of sun
Quattromike
Well member-known
Don't swear at me!how do you insure yourself for jobs like that Mike? ... my cover for the cranes used to be horrendous
V8Druid
do it as well as you can,but learn to do it better
's ok 'til things go a bit Pete Tong
.. can't beat decent cover then ....your 'friendly' customer, you're doing a favour for, becomes snarling Cerbarus
Last edited:
Footer block 1