Noobie

vintage580

vintage580

Member
Farming for my sins in a previous life, bit of forestry as well. Just got a Case 580G which is probably older (1987) than some members here. Not afraid of a bit of spanner work so expect a few noobie questions, and I hope I can contribute here too.
 
V8Druid

V8Druid

do it as well as you can,but learn to do it better
Farming for my sins in a previous life, bit of forestry as well. Just got a Case 580G which is probably older (1987) than some members here. Not afraid of a bit of spanner work so expect a few noobie questions, and I hope I can contribute here too.
as old as my JakieB was then :giggle: ..." plenty a good tune played on an old fiddle " ... did me proud for 10 years ... and yeh .. older than many here :giggle::giggle: went to a new home in July '21, for more than it cost me :love:
WP_20210616_17_28_57_Pro.jpg
WP_20210623_12_44_53_Pro.jpg
WP_20210623_13_15_08_Pro.jpg
 
Mick-the-fitter

Mick-the-fitter

It’s what I do!
I see off to the right in the middle pic, one of the recently mentioned walking diggers! I think someone was looking for one.
 
V8Druid

V8Druid

do it as well as you can,but learn to do it better
Last edited:
Mick-the-fitter

Mick-the-fitter

It’s what I do!
Wasn’t there a member looking for one? I can’t remember the outcome of the conversation!
 
V8Druid

V8Druid

do it as well as you can,but learn to do it better
Wasn’t there a member looking for one? I can’t remember the outcome of the conversation!
Po's bought one in Devon apparently ... think Rory's going to bring it up to Bridgend for him, at some point .... and collect his forks and axles from me, that I picked up from Mog when he was down the road from me last week, doing a job ;) complicated eh :rolleyes::giggle:
 
Mick-the-fitter

Mick-the-fitter

It’s what I do!
Good to hear it works like that👍 Would cost a fortune in hired in transport!
 
Hg2702

Hg2702

Well-known member
Po's bought one in Devon apparently ... think Rory's going to bring it up to Bridgend for him, at some point .... and collect his forks and axles from me, that I picked up from Mog when he was down the road from me last week, doing a job ;) complicated eh :rolleyes::giggle:
If the replacement for the trailer I’m buying turns up so I can replace my trailer and sell that to Rory so he’s got a trailer … just to add to the confusion 🤣
 
C

charlie2

Well-known member
Farming for my sins in a previous life, bit of forestry as well. Just got a Case 580G which is probably older (1987) than some members here. Not afraid of a bit of spanner work so expect a few noobie questions, and I hope I can contribute here too.
the first brand new machine i got trusted with was a 1982 full spec 580g had it for six years and only had one major failure one of the main boom rams broke around the fitting for the hyd hose got it welded up but did it again so new cylinder fixed that. they could push well for a non turbo machine and had a great heater in them.
 
vintage580

vintage580

Member
Thanks for the welcome. First job was to fix the spool lever for tipping the rear bucket, little pin was sitting on the valve chest. Bit of a fiddle getting it back in and then put a new split key in the pin. Next job is an engine oil change, current filter has a July '18 date on it! My 16 year old son trying her out in the muck heap;

IMG_2247.JPG
 
T

topkit

Well-known member
Not a bad machine there I think if i remember correctly case did the 580F and 580G like your one there with 4 in1 front and extending dipper branded as the Construction King basically the Case version of the JCB Sitemaster. You should find plenty of parts still available for that machine.
 
Bri963

Bri963

Well-known member
It lasted into the ‘80’s on the Construction King and the early Cat backhoes had the same boom. It wasn’t until Cat went to the curved boom that they started to get a bit more popular.
 
T

topkit

Well-known member
C J Leonards should be able to help you out on service parts also Warwick Wards and of course good old Ebay.
 
Top