Mogmans creations 🤔

[Monkeybusiness]

reckon there'll be at least a fork carriage going on there

Nah, he’s been fitting rams onto massive scrap handlers. I suspect he’s seen something that will inspire a front end more like this!

 

[6feetdown]

Nah, he’s been fitting rams onto massive scrap handlers. I suspect he’s seen something that will inspire a front end more like this!
View attachment 61434

Puts some perspective on the size of it!

 

[V8Druid]

Nah, he’s been fitting rams onto massive scrap handlers. I suspect he’s seen something that will inspire a front end more like this!
View attachment 61434

yeh I saw the rams on the back of his truck when we met up last month and he dropped off the tico winch .... seeeeeeeeeeeeeeeeeeeeeeeeerious rams

 

[Mogman]

Been way to busy to sort this project out but stuck this on for now

can brush the shed and yard now

 

[Mogman]

Been a bit of a on going project
Rototilt (who I do the transport for the shows) have had a hospitality unit commissioned along with a roof viewing platform and a front deck but the top and floor deck ws made from a shipping container floor and roof cut down and repurposed for the job, but because it was only painted steel and they also used box section in parts couldn’t be painted inside and out it started to hold water that then rusted and would of made some nasty stains down the box also it was very heavy for what it needed to be

So enter Mogman

I put forward a lightweight but strong design (shaved over 500kgs of the viewing platform)and by using aluminium hand rails welded instead of steel scaffolding tubes and connectors made them a 1/3 of the weight too

Then had the upper and lower decks fully galvanised

Before re-decking with the original deck it has an integrated 100mm kicker around the perimeter of the viewing deck with cut outs at both ends to accommodate the stairs (need to re-work them too to please HSE) and make some aluminium handrails for them too that fit better then the original ones

 

[V8Druid]

Been a bit of a on going project
Rototilt (who I do the transport for the shows) have had a hospitality unit commissioned along with a roof viewing platform and a front deck but the top and floor deck ws made from a shipping container floor and roof cut down and repurposed for the job, but because it was only painted steel and they also used box section in parts couldn’t be painted inside and out it started to hold water that then rusted and would of made some nasty stains down the box also it was very heavy for what it needed to be

So enter Mogman
View attachment 68758
I put forward a lightweight but strong design (shaved over 500kgs of the viewing platform)and by using aluminium hand rails welded instead of steel scaffolding tubes and connectors made them a 1/3 of the weight too
View attachment 68759
Then had the upper and lower decks fully galvanised
View attachment 68760
Before re-decking with the original deck it has an integrated 100mm kicker around the perimeter of the viewing deck with cut outs at both ends to accommodate the stairs (need to re-work them too to please HSE) and make some aluminium handrails for them too that fit better then the original ones

bet you had fun prepping that for galving ... and then finding someone who'd do it
what length is it Paul? .. 20 ft?

 

[Mogman]

Yea 20’ x8’ a place in Rochdale has a big bath
Plenty of holes

 

[V8Druid]

Yea 20’ x8’ a place in Rochdale has a big bath
Plenty of holes

A LOT of holes
presumably a double dip?
Hereford Galv used to have a 36ft tank and was the only reason I'd use 'em for some stuff - terrible finish though

 

[DaveDCB]

Very smart!!
Do the handrails have to be secured down? Can imagine a drunk @Monkeybusiness up there getting out of hand and flicking them out!

 

[Mogman]

Very smart!!
Do the handrails have to be secured down? Can imagine a drunk @Monkeybusiness up there getting out of hand and flicking them out!

It has grub screws in the corners that will hold them in/down to stop fooking clowns (yes you @Monkeybusiness) it also will have corner clamps holding the tops together at the corners

 

[Mogman]

Well she’s back on the road
(Not fair hijacking @JD450A tread)

£60 in parts and 6hrs of getting oily

 

[Furniss]

Well she’s back on the road
(Not fair hijacking @JD450A tread)
View attachment 69096
£60 in parts and 6hrs of getting oily

Result

 

[Mogman]

As a lot of you know I do a bit of work for an air con company delivering and lifting units into place
Some of the units have to go to some tight spaces like this

Anyway needed a trailer that I could tow behind the lorry and car but would also be covered so was thinking tautliner but need to remove the roof so I can lift units straight up so need a Dutch style tilt trailer after a long search bought this

Great I thought but it’s 100mm too narrow and 150 too short in hight
Got the sheet off it as will have to get a slightly bigger one made

So the big coffee table made the job a bit easier making it all straight and a bit bigger

So fast forward a few days (other payed work getting in the way again ) and I welded sockets into my original trailer so I can still revert back to a standard flat bed, fixed the drop side hinges to the sides

This is the main reason for the purchase

The whole roof concentians to one end
Now waiting for the new sheet to be made sent the dimensions to them yesterday

 

[DaveDCB]

Oneday you’ll buy something that doesn’t need chopping up before you can use it
Bullshit statement I know

 

[V8Druid]

Oneday you’ll buy something that doesn’t need chopping up before you can use it
Bullshit statement I know

usually the only way to get EXACTLY what you're after

 

[Mogman]

Oneday you’ll buy something that doesn’t need chopping up before you can use it
Bullshit statement I know

No fun in that
Even Alli welded all the holes up for the old fixings on the side boards

 

[rossandson]

Down the side of a BT ATE. @Mogman

 

[Mogman]

Down the side of a BT ATE. @Mogman

View attachment 80791

Don’t I know it some sites I have to fold both mirrors in then it gets proper interesting

 

[Mogman]

A follow on from what I bought today

Cut 2.5 meters off the back of the body this afternoon


And sat it on the trailer to see where it sits needs 20” off the back still and lowering to the trailer deck

Got to cut and make some locating things next so when it gets crained on the trailer it will find its place

 

[TiltyShaun]

A follow on from what I bought today

Cut 2.5 meters off the back of the body this afternoon
View attachment 81001

And sat it on the trailer to see where it sits needs 20” off the back still and lowering to the trailer deck
View attachment 81002
Got to cut and make some locating things next so when it gets crained on the trailer it will find its place

The curtains might need adjusting!!